Ocean Signal Rescueme Mob1 740s-01551 Personal Ais Beacon- Review

What test modes does the MOB1 have?

There are three test modes on the MOB1; Functional, DSC and AIS/GPS.

The Functional exam should be carried out one time a month and volition brandish the length of time the battery has been used for.  Information technology will too apply a load to the battery to test that the battery is not faulty or has been discharged.  It carries out other functional tests on the electronic circuitry.  It does non test the GPS or make examination transmissions.

The DSC test should be carried out no more than two times a year.  This test sends a unmarried DSC manual to the MMSI programmed into the MOB1, which volition be displayed on the vessels DSC radio.  It does not ship a Distress or Distres Relay call and the call does not contain the position.

The AIS test should be carried out no more than than 3 times a year.  This test activates the GPS receiver and afterwards the position is determined it makes an AIS manual, which volition brandish on a suitable AIS receiver or chartplotter.  The received AIS message will show the position determined by the MOB1 GPS receiver.  In that location is also a manual of the AIS text message containing the words "MOB Test".  Note that this exam must exist done with the MOB1 in full view of the heaven.  Without a valid position, the MOB1 will non transmit any AIS letters.

The limitation on the number of tests a year is to ensure that the battery will still have its full operational life at the expiry appointment of the bombardment.

Why does my MOB1 testify ruby-red flashes if I effort to programme the MMSI number?

If the unit of measurement fails to programme, showing the flashing red LED on completion, please try over again.  Turn the MOB1 on in programming mode again and retry.  There is no demand to get out the programming screen on the program.  If the programming page is showing, just printing F10 once more to embark the programming sequence again.  Note that the red flashing may tecke several seconds to showtime after the on screen sequence has finished.

If you are having bug programming your MOB1, please bank check the following guidance.

ane) Make sure that your screen effulgence is fix to maximum, using the controls on the monitor or device.

2) Ensure that you have commenced programming within 50 seconds of putting the MOB1 into programming manner.  Failure to do this volition crusade the MOB1 to take turned off before communication starts.  Note that once programming has commenced (The white box is flashing) the MOB1 should stay on until the programming sequence is completed. Ideally the MOB1 should be put into programming mode just earlier placing the MOB1 in front of the white square.

3) Ensure that the MOB1 is placed over the white foursquare with the rubber programming adaptor firmly touching the screen and with the discontinuity in the prophylactic close to the middle of the white box.

iv) Avoid programming the MOB1 in vivid ambient light weather.  If necessary point the screen away from directly or brilliant sources of light such as sun through a window.  (In extreme circumstances, especially with older screens that have lost their brightness, place a thick material over the screen and MOB1 to block out the ambience light.)

v) The MOB1 configuration software requires precise timing, which may be disrupted by other applications running at the aforementioned time, especially on slower computers.  If you still encounter problems, try shutting downward all un-necessary applications, including anti-virus software.

6) On laptops, the F10 key will require using in conjunction with the Office (labelled Func or Fn) to start the white box flashing black and white to transport the data to the MOB1.  Most keyboards will colour the F keys in the same colour as the Function cardinal to identify this.

vii) The MOB1 MMSI programming software is only available for Windows PCs.  For users of other operating systems and smart phones and tablets in that location is an online application available.  This can exist accessed using the button on the installers web page. Notation that information technology tin but be used online.

Which DSC radios are compatible with the MOB1?

Ocean Bespeak recommends using one of the radios from the list below with the rescueME MOB1. The post-obit class D DSC radios have been tested in cooperation with the manufacturer and confirmed to receive the Individual Distress Relay call.

ICOM:
Current models; M91, M323, M423, M506
Older models; M411, M421, M505, M603

Simrad: RS90

Standard Horizon:   The factory has confirmed the post-obit models are compatible:

GX5500S
V4.twenty (GX5500S only),

<GX2200/GX2150/GX2000>
V5.xx (ALL)
V4.xx (GX2150/GX2000 only)
V1.xx (GX2200 only)

<GX1700/GX1600>
V4.xx (ALL)
V2.xx (ALL)

<GX1300>
V2.xx (ALL)
V1.20 (ALL)

<GX1200>
V1.twenty (ALL)

Class A DSC radios have always been able to receive this call and all models are believed to exist compatible.

This list is not exhaustive and will be added to as more than compatible models are confirmed.

Ocean Signal welcomes enquiries from other manufacturers wishing to accept their radios listed here.

What DSC functions are allowed in my country?

The DSC functionality of the MOB1 is limited by regulations in each state.  The list below indicates which functions you lot may look.

AIS only: Canada, Kingdom of denmark, Latvia

AIS + DSC Individual Distress Relay call plus group phone call sent after 30minutes: United states of america

AIS + DSC Individual Distress Relay call only: France, Germany, Netherlands, Spain, U.k.

AIS + DSC Individual Distress Relay, All Ships Distress Alarm (transmission initiation only): All other European countries

AIS + DSC Individual Distress Relay, All Ships Distress Alert, sent once on MOB1 activation and on manual initiation: Balance of the Globe.

How to programme DSC MMSI number into the MOB1

A video showing the programming sequence for the MOB1 tin can exist found at this link..  Remember to set the display brightness to full before starting the sequence.
Note that the test key is being pressed directly and then the rubber adaptor fitted when the MOB is fix to programme.

Can I cange the DSC MMSI number is I move to a different vessel?

Yes, information technology is possible to reprogram the MMSI number used to call your DSC radio as many times every bit you like using the normal applications. There is no demand to delete the onetime number first. The new number will simply overwrite the old MMSI number.
Each time yous programme the MOB1 it volition apply a small corporeality of the battery chapters and reduce the operating lifetime past a few minutes each time.

Why does the displayed MMSI not change when I enter my DSC MMSI number?

All AIS and DSC MOBs are pre programmed at the time of manufacture with the self identification MMSI number.  In the example of the rescueME MOB1, or the M100, this number volition always commencement 97260—-.  The 972 identities the device equally an MOB device and the sixty identifies the device as manufactured by Ocean Signal.

It is non possible for the user to modify this number, which is a requirement of the relevant approval standards.

The DSC MMSI number programmed in by the user is the number the MOB1 will transport the distress calls to.  Compatible radios volition still show the 'from' MMSI number as the 972 number printed on the rear of the MOB1.  Besides the target displayed on an AIS plotter volition likewise show with the target address as the 972 number.

What is the black cord supplied for?

The provided length of cord is supplied as a safeguard against accidental loss.  The string (lanyard) should be used to tether the MOB1 to a fixed point on the lifejacket that will non inhibit aggrandizement or disassemble/untie if the MOB1 is accidentally removed from its bracket. The MOB1 fixing point for the cord is located on the elevation of the unit.

AIS manual Transmit Power

1Watt

Frequency

161.975/162.025MHz

DSC Transmission Transmit Power

0.5Watt

Frequency

156.525MHz

Messages

Individual Distress Relay Distress Alarm (past single call made on press of the activation button)

Temperature range (operational)

-twenty°C - +55°C

Temperature range (storage)

-30°C - +70°C

Waterproof

10m depth

Weight

92 grams

Standards

RTCM SC11901, EN303 098-1

⚠ WARNING:

This product can betrayal you to chemicals including Bisphenol A (BPA), which is known to the State of California to cause birth defects or other reproductive impairment. For more information go to world wide web.P65Warnings.ca.gov.

hughesjustong.blogspot.com

Source: https://oceansignal.com/products/mob1/

Share this post